Predictive Control of a Three-Phase Neutral-Point-Clamped Inverter

By René E. Vargas, Patricio Cortes, Ulrich Ammann, José Raúl Rodríguez Rodríguez, Jorge A. Pontt. IEEE transactions on industrial electronics (1982. Print), 2007

596 citations recorded by the source corpus.

Subfields: Electrical and Electronic Engineering

View Paper: https://www.semanticscholar.org/paper/c45c114b4ac36329fb2913b05c07b21cc44bcb42

How researchers see this paper

The researchers whose trusted networks rank it highest, strongest advocate first. Every researcher gets a different order.

In Electrical and Electronic Engineering

Citations in the corpus

Weighting Factor Design in Model Predictive Control of Power Electronic Converters: An Artificial Neural Network Approach (2019, methodology): “methodology is carrying out time-consuming simulations and relying on trial-and-error approach to test the effect of different weighting parameter combinations [16].”
Algebraic Tuning Guidelines for Model Predictive Torque and Flux Control (2018, background): “This concept was introduced in [15] and later refined in [16]–[18].”
Recent Advances and Industrial Applications of Multilevel Converters (2010, background): “The use of predictive control in the field of multilevel converters has been introduced very recently as a very attractive and promising alternative [252].”
A Simplified Finite-Control-Set Model-Predictive Control for Power Converters (2014, background): “For example, in the case of a three-level neutral point clamped (NPC) converter, the minimum time needed for completing the FCS-MPC is approximately 52 s [30]; this is still longer than the control loop cycle time required for achieving satisfying control performances.”
State of the Art of Finite Control Set Model Predictive Control in Power Electronics (2013, background): “Similarly, for current control MPC achieved lower absolute error in reference tracking [40], operating at the same switching frequency as a PWM controller.”
Model predictive control of high power converters and industrial drives (2016, methodology): “For higher power ratings, MV generators are used [3].”
A Survey on Neutral-Point-Clamped Inverters (2010, background): “6) Predictive Control [19], [20], [59], [63]: In recent years, increasing attention is being paid to the application of predictive control in the field of power electronics and electrical drives [38], [39].”
Medium-Voltage Multilevel Converters—State of the Art, Challenges, and Requirements in Industrial Applications (2010, methodology): “The method of triangular carrier switching control is well known for the closed-loop control of 2L inverters [155]–[157].”
Model Predictive Control of Multilevel Cascaded H-Bridge Inverters (2010, methodology): “If a lower switching frequency is required, it is possible to reduce it by including a cost to the change of the switching state, as presented in [27].”
Model Predictive Direct Torque Control—Part I: Concept, Algorithm, and Analysis (2009, background): “Similarly, [21] and [22] consider only a resistive inductive load with a back EMF rather than an electric motor.”
Predictive Torque Control of Induction Machines Based on State-Space Models (2009, methodology): “In the same way, it is also possible to include additional constraints in the cost function such as reduction of the switching frequency [7] and imposed spectrum [8].”
“Predictive control in power electronics and drives” (2008, background): “In [60], the possibility of including additional terms to the cost function is proposed, adding capacitor voltage balancing and reduction of the switching frequency.”
Interleaved Model Predictive Control for Three-Level Neutral-Point-Clamped Dual Three-Phase PMSM Drives With Low Switching Frequencies (2021, methodology): “If all the candidates have at least one variable with the predicted value at instant (k+2)Ts beyond the given bound, the similar method as in [25] is used.”
Predictive control based selective harmonic elimination with low switching frequency for multilevel converters (2009, background): “Finally, the third term (5) is used to reduce the number of commutations [10].”