Polyaniline. Preparation of a conducting polymer(IUPAC Technical Report)
By Jaroslav Stejskal, R. Gilbert. Chemistry International, 2002
1,345 citations recorded by the source corpus.
Abstract Eight persons from five institutions in different countries carried out polymerizations of aniline following the same preparation protocol. In a "standard" procedure, aniline hydrochloride was oxidized with ammonium peroxydisulfate in aqueous medium at ambient temperature. The yield of polyaniline was higher than 90 % in all cases. The electrical conductivity of polyaniline hydrochloride thus prepared was 4.4 ± 1.7 S cm-1 (average of 59 samples), measured at room temperature. A product with defined electrical properties could be obtained in various laboratories by following the same synthetic procedure. The influence of reduced reaction temperature and increased acidity of the polymerization medium on polyaniline conductivity were also addressed. The conductivity changes occurring during the storage of polyaniline were monitored. The density of polyaniline hydrochloride was 1.329 g cm-3. The average conductivity of corresponding polyaniline bases was 1.4 x108 S cm-1, the density being 1.245 g cm-1. Additional changes in the conductivity take place during storage. Aging is more pronounced in powders than in compressed samples. As far as aging effects are concerned, their assessment is relative. The observed reduction in the conductivity by ~10 % after more than one-year storage is large but, compared with the low conductivity of corresponding polyaniline (PANI) base, such a change is negligible. For most applications, an acceptable level of conductivity may be maintained throughout the expected lifetime.
Subfields: Bioengineering, Electrical and Electronic Engineering, Polymers and Plastics
View Paper: https://www.semanticscholar.org/paper/211a47d07fb41bac7102980c374c598a71134e99
How researchers see this paper
The researchers whose trusted networks rank it highest, strongest advocate first. Every researcher gets a different order.
In Bioengineering
In Electrical and Electronic Engineering
- Miroslava Trchová
- Jaroslav Stejskal
- Zuzana Morávková
- I. Šeděnková
- I. Sapurina
- G. Ćirić‐Marjanović
- M. A. Shishov
In Polymers and Plastics
- Jaroslav Stejskal
- Miroslava Trchová
- Zuzana Morávková
- I. Šeděnková
- I. Sapurina
- G. Ćirić‐Marjanović
- M. A. Shishov
Citations in the corpus
- Polyphenylene sulfide (PPS): state of the art and applications (2013, background): “The large descending baseline in the spectral region of 4000– 2000 cm-1 was attributed to conduction free electrons in the composite (Steijkal and Gilbert 2002).”
- Conducting polypyrrole nanotubes: a review (2018, background): “2016), where other conducting polymers, such as polyaniline, become nonconducting (Stejskal and Gilbert 2002).”
- Interaction of conducting polymers, polyaniline and polypyrrole, with organic dyes: polymer morphology control, dye adsorption and photocatalytic decomposition (2019, background): “The “standard” polymerization of aniline hydrochloride (Stejskal and Gilbert 2002) yields globular morphology of polyaniline (Stejskal et al.”
- Spectroscopy of thin polyaniline films deposited during chemical oxidation of aniline (2012, methodology): “…hydrochloride or aniline sulfate, in an acidic aqueous medium (Stejskal et al., 1996; Trivedi, 1997; Gospodinova & Terlemezyan, 1998; Stejskal & Gilbert, 2002; Blinova et al., 2007b; Stejskal & Sapurina, 2008; Sapurina & Stejskal, 2011); ammonium peroxydisulfate (APS) being the most common…”